Description

Package Contents

DX30LC2-SR Colour Flashlight
Manual
Spare O-Rings x2
Holster, Nylon
Lanyard
Pocket Clip, Spring Steel
CR123A Battery Magazine
USB Charging Cable (1m AWG24 Copper)
- Thin post for plugging into flashlight
AC to USB Wall Adapter (Output 5V @ 1A) UL Certified [White]
18650 2600mAh Battery (Sanyo Cell)

Flashlight Dimensions
Body Diameter	2.2 cm	Head Diameter	2.3 cm
Length	13.2 cm	Weight (w/o Battery) / (w/ Battery)	67 g / 113 g

Batteries	1 x 18650 2 x CR123A
Operating Voltage	2.7V - 6.0V
Operating Temperature	-25°C to +40°C

Charging Circuit	L950 SC
Input	USB 5V @ 1A+	Max Charging Current	950mA
Charging Logarithm	Constant Current / Constant Voltage
Precise Voltage Detection Design ±1%		No Trickle Charge
Smart Charging Level Report System		Small Current Charging for Low Voltage Batteries (under 3.0V)
Circuit is designed to recharge a single 18650 battery. Do not attempt to recharge CR123A batteries.

LED	Osram 850nm + Cree XP-L HI V3
Colour Group	IR / Cool White	Colour Temperature	850nm / ---- K

XP-L HI V3
LED Lumens	1160 - 980 *	590	221	77	9
OTF Lumens	-	-	-	-	-
FL-1 Lumens	905 - 790 *	475	178	62	7
Run Time (18560)	1 h 30 m	2 h 48 m	8 h 30 m	28 h	200+ h
Run Time (2x CR123A)	48 m	1 h 30 m	5 h	17 h	140 h
Center Lux	20,800 **	-	-	-	-
Peak Beam Intensity	-	-	-	-	-
Beam Throw Distance	288 m **	-	-	-	-

850nm IR (Infrared)
Radiant Flux	1900mW	-	-	-	-
Run Time (18560)	3 h 18 m	7 h 30 m	19 h	45 h	200+ h
Run Time (2x CR123A)	1 h 42 m	4 h	12 h	30 h	140 h

* Max output is reduced by 15% after 200 seconds (3 minutes 20 seconds) to preserve run time.

** PBI, Throw and the beam profile of the XP-L HI are for the models that use it as the forward LED. As this version has it as the side LED, the PBI and Throw should be lower and the profile angles wider.

XP-L HI V3 Forward Profile
Hot Spot	5.2° **	Spill	62° **	Hot Spot Diameter at 100m	9 m **	Spill Diameter at 100m	120 m **

Materials
Body	Aircraft Grade Aluminum
Body Finish	Premium Type III Hard Anodization 400HV
Lens	Impact Resistant Glass w/ Sapphire and Anti-Reflection Coating

Ingress Protection Rating	IP x8	Impact Resistance	1 m
		Submersible Depth	1 m

On/Off Controls	On at Max: Press the tail cap button until click. Tactical On at Max: Slightly press the tail cap button, but don't click. On at Min: Hold the side button then click the tail cap button. Off: Click or release the tail cap button.
Output Selection	Press the side button to cycle by one output. Forward LED Order: Min -> Low -> Med -> High -> Max <- Side LED Order: Low -> Med -> High -> Max -> Max <- Note: The side LED requires advancing output twice at highest output to return to the lowest output.
Forward or Side LED Switching	Hold the side button for at least a second to switch to the other LED. The active LED when turned off will be the active LED when turned on again - this means tactical on of the side LED is possible.